QUICK-DRY ANTI-OXIDENE COATING

​

• PROTECTS AGAINST RUST

• ADHESIVE AND PENETRATING POWERS

• FOR METAL SURFACES

• ECONOMICAL

• PROTECTS CONCRETE SILOS FROM SILAGE ACIDS

 

 

​

​​​​

​

​

​

​

​​

​

​

​

QUICK-DRY ANTI-OXIDENE COATING

Protects Against Rust

Exposed metal surfaces are in constant danger from rust and corrosion. If the damage is not detected early and corrected, it could mean major extra expense. QUICK-DRY ANTI-OXIDENE COATING gives protection against damaging rust and corrosion for virtually all metal surfaces. Its quickdrying action helps prevent further damage - - - practically eliminating any chance of rust on new surfaces.

​

QUICK-DRY ANTI-OXIDENE COATING

Has Adhesive and Penetrating Powers

QUICK-DRY ANTI-OXIDENE COATING is a jet-black, easy-to-apply asphalt coating. Its special formulation allows it to penetrate into rust corroded areas and retard further spreading. For best results, remove rust and scale before applying QUICK-DRY ANTI-OXIDENE COATING. It is pliable enough to expand and contract with the metal, without losing its protective bond. Normal stresses of that type can crack a regular paint surface. The great adhesive and penetrating powers of this product give it superior bond to metal or concrete. It protects metal surfaces against rust and corrosion caused by moisture, most dilute acids, alkalies, salt water or salt spray, stack fumes and other pollutants.

​

QUICK-DRY ANTI-OXIDENE COATING

For Metal Surfaces

For metal surfaces, preparation of the surface is important. It should be free of scale, dirt, peeling paint, rust flakes, or any other loose material. You can remove rust with TRC RUST REMOVER. You can also accomplish such cleaning by use of a wire brush or scraper. Rusted areas need not be scraped down to bright metal. The surface must be dry. (New galvanized steel must be allowed to weather for three months prior to application or washed down with a 3:1 vinegar solution to remove galvanizing film.) On exterior surfaces, drying time is about four hours. A second coat may be applied after that time. Two coats are recommended in salt water areas or where acid rain exists.

​

QUICK-DRY ANTI-OXIDENE COATING

Economical

ANTI-OXIDENE COATING gives effective, lasting protection at a lower cost than standard metal paint. Under adverse conditions — such as salt air, concentration of moisture, acid fumes, and silage acids, TRC ANTI-OXIDENE lasts longer than conventional paints. Economical to use inside concrete silos as an effective barrier against attack by silage acids. ANTI-OXIDENE COATING aids in preventing costly replacements. Without effective protection, tank sections, metal buildings, and metal equipment surfaces all become the victims of destructive corrosion.

​

QUICK-DRY ANTI-OXIDENE COATING

Protects Concrete Silos From Silage Acids

Whether concrete slab or concrete block construction, the inside walls of expensive silos are subjected to attack by destructive silage acids. QUICK-DRY ANTI-OXIDENE COATING is highly resistant to silage acids. Long-lasting — it forms a tough film that expands and contracts with concrete during temperature changes.

​

RECOMMENDED PROCEDURE FOR TREATING INSIDE WALLS OF CONCRETE SILOS WITH TRC QUICK-DRY ANTIOXIDENE COATING

Specially treated to resist oxidation, 880 CROWN & CHASSIS® resists changes in consistency and quality even when stored for long periods of time. It resists separation, has controlled oil bleeding, and under most conditions will not crack, harden, or become thin.

​

1. SURFACE MUST BE CLEAN AND DRY. Clean the surface thoroughly. Scrub off all silage with stiff FIBER BRUSH. DO NOT use brush with metal bristles. If metal bristles get into silage there’s danger to livestock. WASH DOWN the surface if necessary. Allow surface to dry thoroughly.

​

2. Two coats are recommended over uncoated concrete surfaces. Make sure during application that it is well ventilated or proper respiratory protection is used.

​

3. Allow sufficient time between application for previous coating to cure (at least 4 hours).

​

​

​